- [ ] Tripoli:
- [ ] 2 TAP's: Jim Wilkerson, Bob Yanecek
- [ ] 2 TAP approval signatures: Jim Wilkerson, Bob Yanecek
- [ ] 1 TAP physical inspection: Jim Wilkerson
- [ ] 1 TAP present at launch: Jim Wilkerson
- [ ] Support personnel:
- [ ] Tracking: Jim Wilkerson
- [ ] Photography: Eric Albrecht
- [ ] Video: Kent Newman
- [ ] Assembly: Bill Clugston, Scott Bowers
- [ ] Hybrid/GSE: Bill Clugston
- [ ] Full 20# NOX supply: Bill Clugston
- [ ] FRS communication: Jim Wilkerson
- [ ] Transportation & setup: Scott Bowers, Bill Clugston
- [ ] WAC launch coordination:
- [ ] Notify Launch Directors
- [ ] Clarify & agree upon pad, FRS communication, hybrid GSE operation & considerations including launch distance, nitrous spotter
- [ ] GSE coordination (40 lb capable pad with 10' rail at 500')
- [ ] WAC FITS pre-registration
- [ ] Construction:
- [ ] Nose cone assembly
- [ ] Measure chute packing
- [ ] Upper airframe
- [ ] electronics bay
- [ ] custom fin jig
- [ ] Lower airframe
- [ ] Motor mount adapter
- [ ] Motor retention
- [ ] Vent holes
- [ ] Shear pin holes
- [ ] paint test
- [ ] Finishing
- [ ] Recovery:
- [ ] Receive parachutes
- [ ] Check chutes
- [ ] Check harnesses
- [ ] Check connectors
- [ ] Check chute packing
- [ ] Build deployment charges (3X ea)(fresh BP, test first):
- [ ] Check ematch continuity
- [ ] Primary drogue: 1.0 grams
- [ ] Backup drogue: 1.25 grams
- [ ] Primary main: 3.5 grams
- [ ] Backup main: 4.4 grams
- [ ] Fold & tape 2 ea 15' & 25' 1/4" kevlar
- [_] Deployment charge ground test:
- [_] Drogue
- [_] Main
- [ ] Assemble electronics bay:
- [ ] Fresh 9V batteries
- [ ] Ensure G-Wiz MC is pointing up
- [ ] Check altimeter wiring continuity:
- [ ] G-Wiz MC:
- [ ] JP3-1 (pyro +): JP3-10 (shunt)
- [ ] JP3-2 (pyro -): n/a
- [ ] JP3-3 (cluster/stage +): n/a
- [ ] JP3-4 (cluster/stage -): n/a
- [ ] JP3-5 (apogee +): primary drogue
- [ ] JP3-6 (apogee -): primary drogue
- [ ] JP3-7 (low alt +): backup main
- [ ] JP3-8 (low alt -): backup main
- [ ] JP3-9 (comp -): switched ground
- [ ] JP3-10 (comp +): MC battery +
- [ ] RRC2X-40K::
- [ ] J1-1: backup drogue
- [ ] J1-2: backup drogue
- [ ] J2-1: primary main
- [ ] J2-2: primary main
- [ ] J3-1: switched ground
- [ ] J3-2: RRC2X battery +
- [ ] Tug on block wires with tweezers to ensure they're seated firmly
- [ ] Altimeter settings:
- [ ] G-Wiz MC:
- [ ] JP1 (int/ext battery): open
- [ ] JP2/JP6 (pyro inhibit): open
- [ ] JP4 (cluster/stage): n/a
- [ ] JP5 (400/800'): shunt
- [ ] JP7 (): n/a
- [ ] JP8 (telemetry): n/a
- [ ] RRC2X-40K:
- [ ] SW1-1 ((2500/2000')/(1500/1000')): off
- [ ] SW1-2 (redundant/dual): off
- [ ] SW1-3 (+10/0 sec delay): off
- [ ] SW1-4 (+15/0 sec delay): on
- [ ] SW1-5 (low/hi main (SW1)): on
- [ ] Arm & check altimeters (manually short brass terminals as appropriate):
- G-Wiz MC:
beep, beep-beep, beep, beep (batt OK, no cluster/stage, apogee OK, main OK)
- RRC2X-40K:
Power up: long, long, long, short, short (SW1 settings)
Continuity: short, short, short (main & drogue OK)
- [ ] Power off altimeters
- [ ] Insert electronics sled onto All-thread, through rail guides & into electronics bay
- [ ] Tighten down electronics bay bulkheads
- [ ] Ensure arming switch is accessible through altimeter port
- [ ] Arm & check altimeters (manually short brass terminals as appropriate):
- G-Wiz MC:
beep, beep-beep, beep, beep (batt OK, no cluster/stage, apogee OK, main OK)
- RRC2X-40K:
Power up: long, long, long, short, short (SW1 settings)
Continuity: short, short, short (main & drogue OK)
- [ ]] Power off altimeters
- [ ] Motor:
- [ ] Slice & tape 2 ea pre-heater grains
- [ ] Check size & quantity of all nitrous fittings & lines
- [ ] Dry assemble motor
- [ ] Dry fit complete rocket
- [ ] GSE:
- [ ] Weigh empty nitrous tank
- [ ] Fill 20 lb nitrous tank
- [ ] Weigh filled nitrous tank
- [ ] Charge Pratt RTLS
- [ ] Test Pratt RTLS
- [ ] Finish risk/mitigation documentation
- [ ] Finish project binder
- [ ] Packing list:
- [ ] Project binder
- [ ] Rocket:
- [ ] Nose cone
- [ ] Upper airframe
- [ ] electronics bay & retention hardware
- [ ] Lower airframe
- [ ] 98mm/64mm motor mount adapter
- [ ] Motor retention
- [ ] shear pins
- [ ] Recovery:
- [ ] Skyangle Cert 3 XLarge
- [ ] Skyangle Classic II 32"
- [ ] 24" x 24" Nomex
- [ ] 15" x 15" Nomex
- [ ] 2 ea set of 4 deployment charges :
- [ ] Primary drogue: 1.0 grams
- [ ] Backup drogue: 1.25 grams
- [ ] Primary main: 3.5 grams
- [ ] Backup main: 4.4 grams
- [ ] 2 ea 15' & 25' 1/4" kevlar harness
- [ ] 2 ea 1/4" stainless steel Quick Links
- [ ] Motor:
- [ ] M900 case
- [ ] 2 ea M900 grain & phenolic sleeves
- [ ] M900 nozzle & O-rings
- [ ] M900 fill stem
- [ ] vent tube
- [ ] 2 ea preheater grains
- [ ] 2 ea sets of 2 QuickBurst Slim Gem igniters
- [ ] Compression nuts
- [ ] 2 ea fiberglass fill stem sleeves
- [ ] Krytox
- [ ] Electrical tape
- [ ] GSE:
- [ ] Pratt RTLS launch box
- [ ] Pratt RTLS launch controller
- [ ] Pratt RTLS igniter lead
- [ ] 500' launch cable
- [ ] Full 20 lb tank
- [ ] Solenoid/gauge manifold
- [ ] Stainless fill line
- [ ] Hybrid fittings & materials
- [ ] Rail stop
- [ ] Cam straps
- [ ] Duct tape
- [ ] 8' Ladder
- [ ] Masking tape
- [ ] FRS radios
|